Bench Top | SD5C Water Cooler | Water Works
Factory Super Special - 3 Year Warranty
FREE Filter Kit Value $189.00
FREE Shipping Value $115.00 (Cities & Major Regional Areas Only)
Total Free Bonus Value $304.00
Special Ends - 20 December 2024
Call us with any questions on 1300 55 32 82 or 0414 602800
Waterworks™ has been a leader in point-of-use water coolers for over 20 years, starting with the D5 series. While many have tried to copy it, none have matched the quality and longevity of the Waterworks™ D5.
The D5 series features a 14.3-liter high-density polypropylene cold tank that is tough, rustproof, and easy to clean. The hot tank is a 1.8-liter type 304 stainless steel tank with a 500-watt sheathed heater for temperature control, and an easily accessible on/off switch at the back of the unit.
The cabinet of the D5 series comes in a gloss cloud white color and is made with moulded UV-treated ABS top and front panels, and zinc-coated steel sheets with polymer polyester resin on the side panels. The taps are NSF approved, with durable polypropylene lever type taps featuring self-closing design and fast flow. The hot/cold model includes a hot safety tap as standard, with optional push taps available.
The Waterworks™ PNP filter range is available in single, twin, or triple, with the swing & twist design and automatic water shutoff making filter changes simple and tool-free. The CD2 cup dispenser is perfectly color-matched to suit the B5, B10, D5, and D10 coolers, and Waterworks™ paper and plastic cups are made to fit.
Installation of the D5 series should be done in accordance with local plumbing laws, and failure to install a certified pressure limiting valve will void the warranty. The refrigeration system uses gas R134A, with the refrigerant flow controlled by a capillary tube with no moving parts. The compressor is hermetically sealed with an automatic overload protector, and lubricant is not needed. The electrical system is 220v 50hz single phase with a 1.5-meter power cord supplied, and full load current is 1.2 amps. The condenser operates quietly, is air-cooled with no moving parts, and has the following tap performance:
- Tap 1: Approx. 4 - 10°C
- Tap 2: Room temperature
The D5 series has a capacity of 150ml cups/hr at room temperature and the following liters/hr at different temperatures:
- 21°C: 44 cups/hr, 6.6 liters/hr
- 27°C: 32 cups/hr, 4.8 liters/hr
- 32°C: 18 cups/hr, 2.7 liters/hr
The D5 series is covered by a comprehensive 36-month warranty that provides parts and labor coverage from the date of original sale. A copy of the warranty is available upon request.
Drip Tray:
- Concealed lift-out design made of high-impact durable plastic.
- Removable for sanitation, it incorporates an anti-splash grid that diverts drain water into the drip tray.
Taps:
- High impact polypropylene lever type.
- Fast flow and easy to operate.
- Assembled directly onto the reservoir and fully recessed for added protection.
- Taps are 177mm above the drain grid allowing ample room for filling kettles and other tall objects.
- Hot tap has a safety influence.
Top:
- One-piece heat-resistant plastic.
- Rust-proof top provides a flat surface to hold small coffee servers and trays.
Function Status Display:
- Waterworks unique design.
- This exclusive device illuminates a red/green signal indicating the Power/Hot/Cold position of the dispenser.
Cooling Reservoir:
- Constructed of polypropylene plastic, approximately 12 litres in capacity.
- The reservoir features large radius corners to facilitate cleaning.
- The integrated zoned waterway and baffle system prevents ice rings from restricting chilled water flow.
- Cold water capacity below the baffle is 4.2 litres.
- Water above the baffle stays at or about room temperature.
Air Filter:
- Located on the float assembly for easy access.
- The air filter contains a replaceable filter disc with a one-micron membrane media.
Float Assembly:
- One-stage polyethylene float valve system incorporates a primary float valve, which maintains the water level in the reservoir and shuts off when full.
- The system is designed to operate on an incoming water pressure range of 140-700kPa, and a pressure limiting valve should be fitted in situations where the mains pressure may fluctuate to greater than 700kpa.
Refrigeration System:
- Ozone-friendly HFC-134a refrigerant.
- Flow is controlled by a capillary tube, which has no moving parts.
- Condenser is air-cooled static type for silent running. No fan assembly is required.
- Compressor is hermetically sealed, permanently lubricated and protected against motor overload.
Electrical:
- 240 Volts 50Hz single phase.
- A 1.5 metre house cable and 3 pin plug is supplied.
- Full load current is 1.5 amps.
Power Consumption:
- D5C: 0.25kWh/day & 7.5kWh/month
- D5CH: 1.6kWh/day & 48kWh/month
Performance:
- Tap 1 Outlet water 9DC approx
- Tap 2 Outlet water 18DC approx
- Hot Tap Outlet water 88DC approx
Shipping Weight:
- D5C: 20kg
- D5CH: 22kg
Dimensions:
- D5C/D5CH: 310mmW x 310mmD x 1040mmH
- SD5C/SD5CH: 310mmW x 310mmD x 630mmH
Warranty:
- The entire range of Waterworks D5 Series water coolers is covered by a 36 Month Comprehensive Warranty (copy available on request).
- The warranty provides comprehensive parts and labour coverage for the period of 36 months from the date of original sale.
Electrical:
- 240 Volts 50Hz single phase.
- A 1.5 metre house cable and 3 pin plug is supplied.
- Full load current is 1.5 amps.
Performance:
- Tap 1 Outlet water 9DC approx
- Tap 2 Outlet water 18DC approx
Shipping Weight:
- D5C: 20kg
- D5CH: 22kg
Dimensions:
- D5C/D5CH: 310mmW x 310mmD x 1040mmH
- SD5C/SD5CH: 310mmW x 310mmD x 630mmH
Warranty:
- The entire range of Waterworks D5 Series water coolers is covered by a 36 Month Comprehensive Warranty (copy available on request).
- The warranty provides comprehensive parts and labour coverage for the period of 36 months from the date of original sale.